Understanding your 2006 Mitsubishi Endeavor’s onboard diagnostics system is crucial for modern car maintenance. The OBD2 (On-Board Diagnostics II) port is your gateway to accessing valuable data about your vehicle’s health and performance. This article will guide you through understanding the OBD2 port in your 2006 Mitsubishi Endeavor and what kind of information you can retrieve.
Locating the OBD2 Port on Your 2006 Mitsubishi Endeavor
The OBD2 port is a standardized feature in most vehicles manufactured after 1996. In your 2006 Mitsubishi Endeavor, you’ll typically find the OBD2 port located within the driver’s side interior. Common locations include:
- Under the dashboard: Look beneath the steering column, often near the pedals or to the left side.
- In the glove compartment area: Sometimes it’s positioned within or just above the glove box.
- Center console: Less commonly, it might be found in the center console area.
The port is usually a 16-pin trapezoidal connector. Consulting your owner’s manual for the 2006 Mitsubishi Endeavor is always the best way to pinpoint the exact location if you are having trouble finding it.
Accessing Data via the OBD2 Port: What PIDs are Available?
Once you’ve located the OBD2 port, you can use an OBD2 scanner or adapter to read data from your vehicle’s computer system. For the 2006 Mitsubishi Endeavor, using a standard OBD2 scanner with a K-line connection (pin 7) will provide access to a range of Parameter IDs (PIDs).
Keep in mind that with a K-line connection, the data accessible might be somewhat limited compared to more advanced diagnostic systems. However, you can still retrieve valuable information. Here is a list of PIDs that are generally accessible on a 2006 Mitsubishi Endeavor using an OBD2 reader via K-line:
-
Performance & Sensors:
- Accelerometer Sensor (Total, X, Y, Z)
- Air Fuel Ratio (Measured)
- Barometric Pressure (Vehicle)
- Engine Coolant Temperature
- Engine Load
- Engine RPM
- Intake Air Temperature
- Mass Air Flow Rate
- Throttle Position (Manifold)
- Timing Advance
-
Fuel Trim:
- Fuel Trim Bank 1 Long Term
- Fuel Trim Bank 1 Short Term
- Fuel Trim Bank 2 Long Term
- Fuel Trim Bank 2 Short Term
- Fuel Trim Bank 1 Sensor 1 (%)
- Fuel Trim Bank 2 Sensor 2 (%)
-
Oxygen (O2) Sensors (Limited Availability):
- O2 Bank 1 Sensor 1 Voltage
- O2 Bank 1 Sensor 1 Wide Range Equivalence Ratio Lambda
- O2 Bank 1 Sensor 1 Wide Range Voltage
- O2 Bank 2 Sensor 2 Voltage
- O2 Bank 1 Sensor 2 Wide Range Equivalence Ratio Lambda
- O2 Bank 1 Sensor 3 Wide Range Voltage
- O2 Bank 1 Sensor 4 Wide Range Voltage
- O2 Bank 2 Sensor 1 Wide Range Voltage
- O2 Bank 2 Sensor 2 Voltage
- O2 Bank 2 Sensor 2 Wide Range Voltage
- O2 Bank 2 Sensor 3 Wide Range Voltage
- O2 Bank 2 Sensor 4 Wide Range Equivalence Ratio Lambda
- O2 Bank 2 Sensor 4 Wide Range Voltage
-
Trip & Speed Data:
- Average Trip Speed (Stopped or Moving)
- Speed GPS
- Trip Average KPL (Kilometers Per Liter?)
- Trip Average Liters/100km
- Trip Average MPG
- Trip Distance
- Trip Distance (Stored in Vehicle Profile)
- Trip Time (Since Journey Started)
- Trip Time (While Moving)
- Trip Time (Whilst Stationary)
-
Other Parameters:
- Android Battery Level (%) (Scanner Dependent)
- Barometer (Android) (Scanner Dependent)
- Engine KW (at Wheels)
- Horse Power (at Wheels)
- GPS Accuracy
- GPS Altitude
- GPS Latitude
- GPS Longitude
- GPS Satellites
- Hybrid Battery Charge (%)
- Hybrid/Ev Battery Charge Remaining (%)
- Torque (Units?)
- Voltage C Control Module
- Voltage (OBD Adapter)
Note: The availability and accuracy of specific O2 sensor PIDs can vary depending on the number of sensors actually installed in your 2006 Mitsubishi Endeavor and the capabilities of your OBD2 scanner.
Limitations and Advanced Diagnostics
It’s important to understand that using a K-line connection for OBD2 access on your 2006 Mitsubishi Endeavor has limitations. Mitsubishi vehicles, including the Endeavor, utilize a more complex diagnostic system known as MUT-II (Mitsubishi Unified Tester II). Standard OBD2 scanners, especially those relying on K-line, may not access the full range of diagnostic data available through the MUT-II system.
This means that while you can retrieve basic engine and sensor data using the OBD2 port, accessing more in-depth information from other vehicle modules (like ABS, transmission, or airbag systems) might require specialized Mitsubishi diagnostic tools that communicate directly with the MUT-II system.
Furthermore, some advanced functions and complete PID lists might be beyond the scope of basic OBD2 devices on this vehicle. The original Mitsubishi diagnostic software suite and MUT-II/MUT-III systems offer a more comprehensive diagnostic capability.
Conclusion
The OBD2 port on your 2006 Mitsubishi Endeavor is a valuable tool for basic vehicle diagnostics and performance monitoring. Using a standard OBD2 scanner, you can access a useful set of PIDs related to engine performance, fuel trims, and trip data. However, be aware of the limitations of K-line OBD2 access and the existence of the more comprehensive MUT-II system for advanced diagnostics on your Mitsubishi Endeavor. For deeper diagnostics or accessing systems beyond the engine control unit, specialized Mitsubishi diagnostic tools might be necessary.
